Extension cords are invaluable in the trade, we all use them. We haul them off the truck, plug them in and proceed to attach all of our power tools to them. Do you ever inspect them for cracks, cuts, or frayed wires? Believe me I know firsthand the hazards of a small cut in one. It was raining one day, I didn’t give it a second thought. I just kept working, part of my cord was under water, I was using a hammer-drill, installing an outside railing. I got zapped a good one. I was sick to my stomach, had a pounding headache. It could have been a worse. Needless to say I learned my lesson. I check my cords all the time, it only takes a minute. A minute that could save your life.
Safety Guidelines in Selecting Extension Cords
The Following are guidelines to help select the safe and proper extension cord for the tools or equipment that are to be used on the job:
Use the right extension cord. The size of wire in an extension cord must be compatible with the amount of current the cord will be expected to carry. The amount of current depends on the equipment plugged into the extension cord.
Current ratings (how much current a device needs to operate) are often printed on the nameplate. If a power rating is given, it is necessary to divide the power rating in watts, by the voltage, to find the current rating. A 1,000-watt heater plugged into a 120-voltcircuit will need almost 10 amps of current. A 1-horsepower electric motor uses electrical energy at the rate of almost 750 watts, so it will need a minimum of about 7 amps of current on a 120-volt circuit. Electric motors need additional current as they startup, or if they stall, requiring up to 200% of the nameplate current rating. Therefore, the motor would need 14 amps.
Choose a wire size that can handle the total current. Add to find the total current needed to operate all the appliances supplied by the cord. The length of the extension cord needs to be considered when selecting the wire size. Voltage drops over the length of a cord.
When a cord is too long, the voltage drop can be enough to damage the equipment. The larger the size of the wire, the longer the cord can be without causing a voltage drop that could damage tools and equipment. Grounding paths must be kept intact to keep you safe.
A typical extension cord grounding system has four components:
• A third wire in the cord, called a ground wire.
• A three-prong plug with a grounding prong on one end of the cord.
• A three-wire, grounding-type receptacle at the other end of the cord.
• A properly grounded outlet.
Inspection and Tests for Extension Cords
Extension cords should be inspected regularly using the following procedure:
• Remove the cord from the electrical power source before inspecting.
• Make sure the grounding prong is present in the plug.
• Make sure the plug and receptacle are not damaged.
• Wipe the cord clean with a diluted detergent and examine for cuts, breaks, abrasions, and defects in the insulation.
• Coil or hang the cord for storage. Do not use any other methods.
• Coiling or hanging is the best way to avoid tight kinks, cuts, and scrapes that can damage insulation or conductors.
Test extension cords regularly for ground continuity using a continuity tester as follows:
• Connect one lead of the tester to the ground prong at one end of the cord.
• Connect the second lead to the ground wire hole at the other end of the cord.
• If the tester lights up or beeps, the cord’s ground wire is okay. If not, the cord is damaged and should not be used.
• Do not pull on cords; always disconnect a cord by the plug.
• Use electrical plugs and receptacles that are right for your current and voltage needs. Connectors are designed for specific currents and voltages so that only matching plugs and receptacles will fit together. This safeguard prevents a piece of equipment, a cord, and a power source with different voltage and current requirements from being plugged together. Standard configurations for plugs and receptacles have been established by the National Electric Manufacturers Association (NEMA).
• Use locking-type attachment plugs, receptacles, and other connectors to prevent them from becoming unplugged.
Jacket Information: S: 600V Service Cord; J: 300V Junior Service; T: Thermoplastic; E: Thermoplastic Elastomer;
O: Oil Resistant Outer Jacket; OO: Oil Resistant Outer Jacket and Oil Resistant Insulation; W: Approved for Indoor/Outdoor use(Weather/Water Resistant).
Conclusion: Ground fault circuit interrupter (GFCI) protection is required on construction sites.